Your search for '斗破苍穹章节'
returned
5,642 results.
|
Oval Knife Guard #6 , 9/16" wide by 1-3/32" long,, 1/16" thick, small rectangular slot 1/8" wide by 3/8" long, brass
Oval Knife Guard #6 , 9/16" wide by 1-3/32" long,, 1/16" thick, small rectangular slot 1/8" wide by 3/8" long, brass
|
|
Oval Knife Guard #6 , 9/16" wide by 1-3/32" long,, 1/16" thick, small rectangular slot 1/8" wide by 3/8" long, nickel silver
Oval Knife Guard #6 , 9/16" wide by 1-3/32" long,, 1/16" thick, small rectangular slot 1/8" wide by 3/8" long, nickel silver
|
|
American black walnut knife handle scales , two scales 3/8" x 1-1/2" x 5"
Our American black walnut, is selected for density and figure, if possible. Our scales are slabs of wood, selected for closely matching grain, figure, and color. Rivet, pin, or glue one scale to each side of your flat sided knife handle, then carve, file, grind, sand, or belt-sand the handle scales to the exact grip shape you desire.
|
|
Gunsmithing Labor : install breech plug, fitted inside
Our gunsmith will install a breech plug we offer, in a barrel we offer, with the front face of the breech plug tightly sealed against the inside shoulder of the breech thread, and the barrel maker's name (if any) indexed to the bottom flat. Threads are lubricated with Birchwood Casey's Choke Tube Lube anti-seize, so the plug may be removed, even af
|
|
|
Gunsmithing Labor: cut and crown the muzzle
We face the muzzle end square with the bore, then crown the bore until the sharp edge of the lands and grooves are chamfered to allow easy loading. This "minimum crown" produces best accuracy, and can be chamfered further, if desired, for faster loading. Specify the desired barrel length, and whether plug is included in length. When shortening a qu
|
|
|
Gunsmithing Labor : mill dovetail & install sight, per operation
Prompt service : Our gunsmith will mill a dovetail for a front sight, rear sight, or underlug we offer, using a milling machine and dovetail cutter. Hand fitted : no extra cost! When you buy the sights or lugs from us, we will remove any burrs, gates and parting lines, and hand fit the sight or lug to the dovetail slot, ready for you to finish an
|
|
|
Gunsmithing Labor: drill and tap blind hole to install rib, per operation
We drill and tap blind holes, usually 5-40, drill, counter-bore and mount the rib. Rifles usually require four(4) screws. Specify stock forend length. Forends are most often 13 to 16" length, while ribs are 24" length. Thus, they will fit a barrel of 37 to 40" length. Longer ribs available at extra cost. Half stock pistols require two mounting hole
|
|
|
Gunsmithing Labor: re-thread barrel breech for plug
Rarely needed, unless you wish to shorten a barrel without cutting the muzzle. We always recommend saving the muzzle by shortening at the breech to eliminate a visibly off center muzzle due to possible run-out. We can cut most standard threads. Price includes shortening the breech and re-threading for the plug. Removing an old plug is additional co
|
|
|
Gunsmithing Labor: mill and solder ramrod pipe to rib, price each
We mill a flat on each rod pipe, and a matching flat notch in the rib. After "tinning" both flats with solder, we clamp the pipe, heat the joint, and cause the two solder coated surfaces to be joined. We require fitting the underrib and breech plug before performing this operation.
|
|
|
Gunsmithing Labor : mill dovetail and fit adjustable Hawken rear sight
Prompt service : Our gunsmith will mill a dovetail for your Hawken adjustable rear sight, or underlug, using a milling machine and dovetail cutter and hand fit the sight with rizer. When you buy the sight from us we remover parting lines, and hand fit the sight with rizer to the dovetail slot, ready for you to finish and use. Many of our rear sigh
|
|
|
Gunsmithing Labor : install lug staple, or dovetail lug, for key or pin, per operation
Underlug staples were used on original guns! English, American, and European rifles, fowling guns, and shotguns were sometimes fitted with underlug staples. Prompt service : Our gunsmith will install our underlug staple, for standard (halfstock size) wedge key, small (fullstock size) wedge key, or for a round steel dowel pin. Shop time typically
|
|
|
Gunsmithing Labor : install soldered part, sight or lug, per operation
Round barrels sometimes require soldered lugs or sights. Thin walled barrels often require soldered lugs or sights. Prompt service : Our gunsmith will install our underlug using solder, for standard (halfstock size) wedge key, small (fullstock size) wedge key, or for a round steel dowel pin. Shop time typically requires 7 to 10 days for labor. Un
|
|
Latigo leather strap , 3/8" wide, 54" long
A strong leather strap, 3/8" wide, 54" long, in a rich dark chocolate brown. Excellent for making a powder horn strap, extra ties for your possibles bag, bedroll lacing, and all other sorts of uses. Nice quality latigo leather.
|
|
Trekker's Lantern , brass
This small lantern measures 4-1/8" tall with a 1-5/8" diameter base. The two oval steel rings act has handles and give the lantern added stability when placed on a flat surface. The rings fold along the back side of the lantern for convenient storage. The perfect lantern for the trekker, re-enactor, or period camper. Also available in copper .
|