This trap gun has a modern style with the black walnut stock adjustable for both length of pull and comb height. The stock is shaped with a checkered pistol grip and the forearm flares wide at the end. The stock has no provision for a ramrod and would normally be loaded at a bench. We note one repair to the stock on the forward lock panel were the stock was glued along a grain boundary that angled into the lock mortise. Currently the trigger reach is 14-1/4". Weight is 6 pounds.
The 27" barrel is tapered round with a 12 gauge bore. The muzzle end is fitted with a screw in choke that constricts down to a 0.720" bore diameter. Your options for loading are wool wads, or traditional cards and wads. For loading traditional card wads through a choke, the card manufacturer recommends using a 12 gauge over powder card pushed through the choke sideways, so only two sides of the card are flattened. A smaller 14 gauge fiber wad is used. The thin over shot card can easily pass through a choke without any difficulty. The barrel is stamped 12 ga. and M. J. Longstreth Dayton Ohio on the breech with individual stamps, so they are not quite even. The barrel has a hooked breech and can be dismounted with a screw on the bottom of the forearm. Remove that screw and lift the barrel up from the muzzle end to dismount the barrel from the tang.
The 1820 era Ketland flintlock is perhaps the most popular style of flint lock found on fine original antique American longrifles. This attractive medium size rifle lock is based on our best Siler internal lock parts. The pan is rounded in English fashion. The tail of the lock plate is slightly lower than the raised panel that forms the lock plate, separated by an attractive molding. The frizzen glides over a roller bearing on the frizzen spring, which is retained by a hidden mounting screw. The Ketland family of lock makers were quick to incorporate the best new features in their rifles, fowlers, and flint locks. We recommend our 3/4" knapped English flints for use with this lock.
Fast ignition is assured by the steel vent liner, positioned well above the bottom of the pan, centered on the heat of the flash. If your flint longrifle suffers from that infamous slow whoosh-bang ignition delay, study the work of today's best gun makers, and position your vent well centered on the pan, high above the bottom, to serve as a window on the center of the flash.
A used shotgun for black powder flintlock trap shooting. Order it for a ten day visual inspection. You will be delighted. Else if it does not fit you, return it in unfired condition for same-day refund. Postage is your only risk, when you order any one-of-a-kind gun from Track, whether new, used, or antique.
The 27" barrel is tapered round with a 12 gauge bore. The muzzle end is fitted with a screw in choke that constricts down to a 0.720" bore diameter. Your options for loading are wool wads, or traditional cards and wads. For loading traditional card wads through a choke, the card manufacturer recommends using a 12 gauge over powder card pushed through the choke sideways, so only two sides of the card are flattened. A smaller 14 gauge fiber wad is used. The thin over shot card can easily pass through a choke without any difficulty. The barrel is stamped 12 ga. and M. J. Longstreth Dayton Ohio on the breech with individual stamps, so they are not quite even. The barrel has a hooked breech and can be dismounted with a screw on the bottom of the forearm. Remove that screw and lift the barrel up from the muzzle end to dismount the barrel from the tang.
The 1820 era Ketland flintlock is perhaps the most popular style of flint lock found on fine original antique American longrifles. This attractive medium size rifle lock is based on our best Siler internal lock parts. The pan is rounded in English fashion. The tail of the lock plate is slightly lower than the raised panel that forms the lock plate, separated by an attractive molding. The frizzen glides over a roller bearing on the frizzen spring, which is retained by a hidden mounting screw. The Ketland family of lock makers were quick to incorporate the best new features in their rifles, fowlers, and flint locks. We recommend our 3/4" knapped English flints for use with this lock.
Fast ignition is assured by the steel vent liner, positioned well above the bottom of the pan, centered on the heat of the flash. If your flint longrifle suffers from that infamous slow whoosh-bang ignition delay, study the work of today's best gun makers, and position your vent well centered on the pan, high above the bottom, to serve as a window on the center of the flash.
A used shotgun for black powder flintlock trap shooting. Order it for a ten day visual inspection. You will be delighted. Else if it does not fit you, return it in unfired condition for same-day refund. Postage is your only risk, when you order any one-of-a-kind gun from Track, whether new, used, or antique.
Related Products Shown Below
Track's best Black Powder BORE CLEAN Solvent, with flip-top spout
Bore mop, 100% Cotton, for .75 caliber, 10-32 thread, washable
Ball puller, steel screw, .69 caliber brass collar, 10-32 thread
English Powder Dipper,
adjustable brass cup, calibrated in drams of black powder,
patterned from an antique, made in the U.S.A.
English Shot Dipper,
adjustable brass cup, calibrated in ounces of shot,
patterned from an antique, made in the U.S.A.
French amber gun flint, 3/4 x 7/8" for standard rifle, large Siler, L&R, most others. We are temporarily limiting purchase of this item to twelve per order. We will manually edit your order if your order exceeds that amount.
Button jagged cleaning tip, 12 gauge, brass, 10-32 thread
LEE Adjustable Shot Dipper, adjusts from 7/8 to 1-7/8 oz.
Powder measure, brass, adjustable 0 to 120 grains, with spout
12 gauge shotgun Premium Lubed Wad,
bag of 100 lubricated felt wads
Ramrod,
7/16" hickory, 47" long, brass tip, 10-32 thread
Made in the U.S.A.
Ramrod,
7/16" synthetic Delrin, almost unbreakable rod,
47" long, brass tip, 10-32 thread
Made in the U.S.A.
Buckshot #000
.350" round balls, lead,
by Hornady, 5 pounds
Buckshot #00
.330" round balls, lead,
by Hornady, 5 pounds
Buckshot #4
.240" round balls, lead,
by Hornady, 5 pounds
Speed Loader,
for shotgun, pack of 4 tubes,
magnum load holds 3-3/4 drams (100 grains) of FFg black powder, and 1-1/4 ounce of shot,
ideal for up to 10 gauge guns
12 gauge, .740" ideal for .729" bore, .125" over powder card, 1000, by Circle Fly Wads
12 gauge, .740" ideal for .729" bore, .025" over shot card, 1000, by Circle Fly Wads
14 gauge, .703" ideal for .693" bore, .500" thick fibre wad, 500, by Circle Fly Wads
Patch puller worm, double tine, steel, 10-32 thread, made in the U.S.A.
DIPPER-P-35
English Powder Dipper,
adjustable brass cup, calibrated in drams of black powder,
patterned from an antique, made in the U.S.A.
DIPPER-S-15
English Shot Dipper,
adjustable brass cup, calibrated in ounces of shot,
patterned from an antique, made in the U.S.A.
FLINT-AMBER-6
French amber gun flint, 3/4 x 7/8" for standard rifle, large Siler, L&R, most others. We are temporarily limiting purchase of this item to twelve per order. We will manually edit your order if your order exceeds that amount.
RAMROD-S-7-10-B
Ramrod,
7/16" synthetic Delrin, almost unbreakable rod,
47" long, brass tip, 10-32 thread
Made in the U.S.A.
SPEED-SG-ML
Speed Loader,
for shotgun, pack of 4 tubes,
magnum load holds 3-3/4 drams (100 grains) of FFg black powder, and 1-1/4 ounce of shot,
ideal for up to 10 gauge guns
WAD-12-A
12 gauge, .740" ideal for .729" bore, .125" over powder card, 1000, by Circle Fly Wads
WAD-12-B
12 gauge, .740" ideal for .729" bore, .025" over shot card, 1000, by Circle Fly Wads
WAD-14-C
14 gauge, .703" ideal for .693" bore, .500" thick fibre wad, 500, by Circle Fly Wads