Rear sight elevation screw, for Thompson Center Hawken, Renegade, and New Englander. 4-40 threads, adjustment clicks, blued steel. Head diameter 0.31". Will not fit the Cherokee, or Seneca rear sights.

Rear sight elevation screw, for early production Thompson Center Hawken, Renegade, and New Englander. 5-40 threads, adjustment clicks, blued steel. Head diameter 0.31". Will not fit the Cherokee, or Seneca rear sights.

Carved from plain maple, fancy maple, or American black walnut this Hawken Pistol halfstock is, pre-shaped, right hand, inlet for a 15/16” octagon barrel with a channel length of 6". Not inlet for lock or trigger. Hand inlet a lock and a single, or single set trigger of your choice. Not drilled for a ramrod. Drill this for a 1/4" ramrod using the b

Carved from plain maple, fancy maple, or American black walnut this Hawken Pistol fullstock is, pre-shaped, right hand, inlet for a 15/16” octagon barrel up to 10" long. Not inlet for lock or trigger. Hand inlet a lock and a single, or single set trigger of your choice. Drilled full depth for a 3/8" ramrod. Use this stock to build a fullstock, or h

These are copies of original toeplates found on Hawken full-stocks, half-stocks, and German rifles. Toeplate width at widest point is 0.69"

These are copies of original toeplates found on Hawken full-stocks, half-stocks, and German rifles. Toeplate width at widest point is 0.66"

These are copies of original toeplates found on Hawken full-stocks, half-stocks, and German rifles. Toeplate width at widest point is 0.70"

These are copies of original toeplates found on Hawken full-stocks, half-stocks, and German rifles. Toeplate width at widest point is 0.68"

This toeplate has a beavertail finial, used on Hawken, Dimick, and Plains rifles. Toeplate width at widest point is 0.69"

This toeplate has a beavertail finial, used on Hawken, Dimick, and Plains rifles. Toeplate width at widest point is 0.69"

Stirrup link, wax cast steel, tempered, integral pins.

frizzen spring screw, 6-40 thread

top jaw screw, slotted, 1.3", 1/4-28 thread

Our wrenches feature a high carbon steel body with a low carbon steel rod handle. Special commercial tempering gives optimum strength to the wrench fingers. The malleable handle will flex if excess torque is applied, to avoid damage. Our wrenches are not unbreakable, but they are pretty close! This well tempered nipple wrench has two sturdy fingers

Small pistol front sight a tiny dovetail base, only .245" long, .045" deep, about .557" wide. Used on our 15/16" pistol barrel, the blade stands .160" above the base and measures .085" wide. Machined brass.

Bridle, wax cast, drilled, Thompson Center Hawken lock

Frizzen, tempered, blued, for Thompson Center Hawken flintlock

Frizzen spring, tempered, blued, for Thompson Center Hawken flintlock

Mainspring, tempered, coil style, Thompson Center Hawken lock

Mainspring plunger, tempered, Thompson Center Hawken lock

Sear, wax cast steel, tempered, with integral axle Thompson Center Hawken lock

Sear spring, coil spring, tempered, Thompson Center Hawken lock

Sear spring plunger, cap for coil spring, Thompson Center Hawken lock

Tumbler, wax cast steel, tempered, right hand, Thompson Center Hawken percussion and flint locks

Malleable steel, the tang may be straightened or bent cold. X-ray inspected for internal flaws. The short .500" thread depth allows a very strong thread engagement when seated to the inside shoulder. It requires flash hole liner for flint use, or a powder drum for percussion use, each sold separately. The powder chamber is .26" diameter, to permit