A one piece hardened steel decapping rod and extra seating screws for all popular bullet nose shapes, and all steel construction.

Straight wall rifle cases require these three die sets consisting of a full length resizing die with decapping stem, a two step neck expanding "M" die and a bullet seating die.

A one piece hardened steel decapping rod and extra seating screws for all popular bullet nose shapes, and all steel construction.

Many black powder cartridge rifle loads require compression for proper ignition. Firm neck tension helps provide compression. Taper Crimp Dies have minimum taper, allowing you to apply proper neck tension, without damaging the bullet, for best accuracy.

This handy tool removes internal flash hole burrs. Features a tool steel cutter which is inserted in the flash hole through the neck case. Adjustable stop collar allows use with any size case.

Useful when melting down scrap lead, emptying your furnace, or when blending alloys. Each mold forms four, easy-to-use ingots that stack easily and weigh approximately 1 pound each. Sides have a 30o draft for easy release. The wooden handle is comfortable.

The cast iron head is shaped for easy, accurate pouring and prevents air pockets in the finished bullet. The long stem makes this dipper cool to handle, and can also be used for stirring molten lead alloys. The wooden handle makes the dipper comfortable to use. Ladle is almost 2-1/4" wide. about 12" length. Now threaded on both the right and left,

This cast iron pot is shaped with a convenient pour spout. It allows the caster to use any heat source for melting lead alloys. Nominal pot capacity is ten pounds. Flat bottom to prevent tipping.

This precision tool allows reloaders to assure uniform prime depth which produces consistent ignition and improves accuracy. Uniforming tool has a pre-set stop collar set to SAAMI specs. For cartridges that use small rifle and pistol primers.

This fixed rear sight is intended for a barrel up to 15/16" octagon. Tall, to reduce heat mirage, a square center notch is cut .070" wide by 0.10" deep. Wax cast steel, made in the Italy., the dovetail is about .350" long and .625" wide by .055" deep. Height from the bottom of the dovetail to the top of the sight notch is 0.45".

Electronic caliper features a high tech design with direct digital readout. Switch back and forth from inches to millimeters with a touch of a button. All new hold setting plus on/off switch. Accurate to .001"/0.1mm. Comes in a handy plastic storage case.

This large size deburring tool was designed for inside and outside deburring of cartridge cases from .17 caliber to .45 caliber. Ideal for the black powder cartridge shooters. The 30 degree angle cutter bevels inside the mouth of the case allowing the bullets to slide in without deforming.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.

This tool works like a depth gauge, trimming any excess brass. Debur inside and outside of the case mouth, using the chamfer tool.