Lock plate, percussion, wax cast steel, drilled and tapped, for L&R RPL-03 percussion T/C Hawken lock

Lock plate, percussion, wax cast steel, drilled and tapped, for L&R RPL-05 percussion Lyman Great Plains, Cabela's, or InvestArm Hawken lock.

Ammunition & Supplies for your 10 gauge percussion shotgun.

Ammunition & Supplies for your 12 gauge percussion shotgun.

Ammunition & Supplies for your 16 gauge percussion shotgun.

Ammunition & Supplies for your 20 gauge percussion shotgun.

Ammunition & Essentials for .32 percussion guns

Ammunition & Essentials for .36 percussion guns

Ammunition & Essentials for .40 percussion guns

Ammunition & Essentials for .45 percussion guns

Ammunition & Essentials for .50 percussion guns

Ammunition & Essentials for .54 percussion Sharps

Ammunition & Essentials for .58 percussion guns

Ammunition & Essentials for .62 percussion guns

Ammunition & Essentials for .69 percussion guns

This percussion lock will replace and upgrade the large percussion lock on the CVA or Traditions Hawken Rifle, from Spain. Overall length 4.99” x 0.98" width. Right hand only. NOTE: this lock wll not fit the Traditions Woodsman or Traditions St. Louis Hawken. This lock has thicker stronger internal springs and parts than the Connecticut Valley Arms

This new percussion lock will replace the percussion lock on the Thompson Center, Hawes brand imported Hawken, or early Lyman Plains rifle. Overall length is 5" x 1" width. The bridle is threaded 8-32 for factory T/C lock bolt. Right hand only. This lock has thicker stronger internal springs and parts than the Thompson Center Arms lock. It requires

This new percussion lock will replace the Dixie Tennessee Mountain rifle lock. A new lock bolt is included. This percussion longrifle is nearly always stocked in cherry, trimmed in iron, marked "JAPAN" on the barrel, made by Miroku, Japan, for Dixie Gun Works. It nearly always has double set triggers, and often has a grease hole bored in the buttst

Nipple, 6-.75mm metric thread, for some pre-1980 imported replica percussion revolvers by A.S.M. or Uberti with metric threads often marked FIE. May be too short for later producion percussion revolvers, #11 CCI cap, hardened steel

Nipple, 6-.75mm metric thread, for some pre-1980 imported replica percussion revolvers by A.S.M. or Uberti with metric threads often marked FIE. May be too short for later producion percussion revolvers, #11 CCI cap, stainless steel

Investarms Percussion Lock right hand lock assembly for Investarms produced Lyman Great Plains Rifle, Deerstalker, Trade Rifle. Also used on Investarms Hawken, Gemmer & Bridger Hawken. Manufactured by Investarms, Italy.

This model will replace the small Spanish Maslin percussion lock, and the similar locks by Russ Hamm, CVA, Traditions, Cochran, and Armsport. The rear of the lockplate has a pre-indicated marking for trimming to the round tail versions of these locks. Overall length is 4-1/2" x 7/8" width. Right hand only. This lock has thicker stronger internal sp

This percussion lock will upgrade and replace the lock on the Lyman Great Plains Rifle, Cabela's Hawken, or InvestArm Hawken, Investarm Gemmer Hawken, or Investarm Bridger Hawken. Overall length is 5-1/16" x 1" width. Right hand only. This lock has thicker stronger internal springs and parts than the Lyman Great Plains Rifle, InvestArm Hawken, or

This percussion lock was made by Thompson Center, for their Greyhawk rifle. It is the same design as the lock used on Hawken, Renegade, New Englander, White Mountain Carbine, and Pennsylvania Hunter rifles, except in stainless steel, and could be used on those rifles. The photo is representative! This used lock is in perfect working order, very goo

This percussion lock was made by Thompson Center, for their Hawken, Renegade, New Englander, White Mountain Carbine, and Pennsylvania Hunter models. The photo is representative! This used lock is in perfect working order, very good condition. Right hand, the lock plate and hammer are factory engraved, and color case hardened. Notice the late style