Track's new nipples - for the traditional purist
hardened and tempered carbon steel, as original:
Purists will appreciate our temper blued steel nipples, made from traditional carbon steel, as were the original nipples. Hardened and tempered to Rc 38 - 44, these long lasting nipples require hot water cleaning after each day's use, as original. Coat the nipple threads with Birchwood Casey's Choke Tube Lubricant to allow easy removal, even after a long day of competition shooting.
Discard the factory made blued steel nipples supplied on imported replica guns, especially revolvers. Made to fit some unknown European cap, they have too much taper to prevent cap fragments from falling into the hammer notch, jamming your revolver. Our nipples fit CCI & RWS No. 11 standard caps correctly.
Track's 416 stainless steel nipples:
Made from 416 alloy (12% Chromium), the first free machining stainless alloy with Martensitic qualities (hardenable, tempers normally, and is magnetic unlike most stainless alloys). Stronger, tougher, more resistant to battering, 416 alloy is longer lasting than the famous old Ampco bronze nipples, now obsolete.
Truly precision turned, our nipples have tapered cones made to perfectly fit the CCI brand No. 11 standard cap, or the identical Dynamit - Nobel RWS brand No. 1075 (red label) cap. Remington No. 11 caps are a tiny bit larger, an easy fit. Track has improved the fit, and extended the life of our percussion nipples.
The values shown for the overall length, thread journal length, and diameter of the base are ideal values and may vary slightly due to machining tolerances. We have noted a wide variety of nipple threads and lengths used on imported rifles and percussion revolvers, even on the same model from the same maker. We recommend confirming the thread, overall length, thread journal length, base diameter, and comparing the cone length. Cone length = overall length minus thread journal length. The cone length must be similar in length to the original nipple to assure good function especially in percussion revolvers.
|
|
Nipple, 5/16-24 thread, for Springfield musket, #11 CCI cap, stainless steel
- Cone length: 0.475"
- Thread journal length: 0.275"
- Overall length: 0.750"
- Diameter of base: 0.370"
|
|
|
|
Nipple, 12-28 thread, for for most A.S.M brand 1860 Colt revolvers, #11 CCI cap, hardened steel
- Cone length: 0.300"
- Thread journal length: 0.200"
- Overall length: 0.500"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 12-28 thread, for most A.S.M brand 1860 Colt revolvers, #11 CCI cap, stainless steel
- Cone length: 0.300"
- Thread journal length: 0.200"
- Overall length: 0.500"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 12-24 thread, used in some FIE marked 1849 Colt pocket model revolvers #11 CCI cap, hardened steel
- Cone length: 0.240"
- Thread journal length: 0.225"
- Overall length: 0.465"
- Diameter of base: 0.275" (this small diameter requires grinding the wrench outside diameter to fit)
|
|
|
|
Nipple, 6-.75mm metric thread, for some early imported replica percussion revolvers, often marked FIE, may be too short for later producion percussion revolvers, #11 CCI cap, hardened steel
- Cone length: 0.275"
- Thread journal length: 0.225"
- Overall length: 0.500"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 6-.75mm metric thread, for some early imported replica percussion revolvers, often marked FIE, may be too short for later producion percussion revolvers, #11 CCI cap, stainless steel
- Cone length: 0.275"
- Thread journal length: 0.225"
- Overall length: 0.500"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 6-.75mm metric thread, .300" long cone for some FAP - Pietta Remington, Pietta Colt, Pietta Le Mat replica revolvers, #11 CCI cap, hardened steel
- Cone length: 0.300"
- Thread journal length: 0.225"
- Overall length: 0.525"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 6-.75mm metric thread, .319" long cone for most FAP - Pietta Remington, Pietta Colt, Pietta Le Mat replica revolvers, fits Pietta 1873 Colt Percussion, #11 CCI cap, hardened steel
- Cone length: 0.319"
- Thread journal length: 0.225"
- Overall length: 0.544"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 6-.75mm metric thread, .319" long cone for most FAP - Pietta Remington, Pietta Colt, Pietta Le Mat replica revolvers, fits Pietta 1873 Colt Percussion, #11 CCI cap, stainless steel
- Cone length: 0.319"
- Thread journal length: 0.225"
- Overall length: 0.544"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 6-.75mm metric thread, .300" long cone for some FAP - Pietta Remington, Pietta Colt, Pietta Le Mat replica revolvers, #11 CCI cap, stainless steel
- Cone length: 0.300"
- Thread journal length: 0.225"
- Overall length: 0.525"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 6-.75mm metric thread, for some early imported replica percussion revolvers, will likely be too short for current reproduction revolvers, #11 CCI cap, stainless steel
- Cone length: 0.260"
- Thread journal length: 0.225"
- Overall length: 0.485"
- Diameter of base: 0.307"
|
|
|
|
Breech Plug with integral nipple
for later production Thompson Center Scout
Carbine, Rifle, or Pistol,
fits No. 11 CCI cap.
Made in the U.S.A. of 416 stainless steel.
|
|
|
|
Breech Plug with integral nipple
for early production Thompson Center Scout
Carbine, Rifle, or Pistol,
fits No. 11 CCI cap.
Made in the U.S.A. of 416 stainless steel.
|
|
|
|
Nipple, .225-32 thread, for antique Colt, Remington, or Savage revolvers, .475" length,
#11 CCI cap, hardened steel, ideal for restoration
- Cone length: 0.300"
- Thread journal length: 0.175"
- Overall length: 0.475"
- Diameter of base: 0.290"
|
|
|
|
Nipple, .225-32 thread, for antique Colt, Remington, or Savage revolvers, .475" length,
#11 CCI cap, stainless steel
- Cone length: 0.300"
- Thread journal length: 0.175"
- Overall length: 0.475"
- Diameter of base: 0.290"
|
|
|
|
Nipple, 12-28 thread, for Ruger Old Army revolver, #11 CCI cap, stainless steel, for Ruger hex socket or Track's #NW-130 wrench
- Cone length: 0.270"
- Thread journal length: 0.260"
- Overall length: 0.530"
- Diameter of base: 0.285"
|
|
|
|
Nipple, 1/4-28 thread, short for T/C rifles, #11 CCI cap, stainless steel
- Cone length: 0.300"
- Thread journal length: 0.200"
- Overall length: 0.500"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 1/4-28 thread, 1/4" height for Classic Arm "Snake Eyes" pistol & Classic Arms "Ethan Allen" Pepperbox pistol, #11 CCI cap, stainless steel. Use nipple wrench NW-170
- Cone length: 0.255"
- Thread journal length: 0.155"
- Overall length: 0.410"
- Diameter of base: 0.365"
This nipple will not fit Hoppe's - Ethan Allen brand replica Snake Eyes pistols.
|
|
|
|
Nipple, 12-28 aka 5.5-.9mm metric thread, for most brands of .31/.36 Colt and Remington pocket revolvers and many Uberti 1851, 1860, 1861 Colt & 1858 Remington revolvers, Colt brand second generation 1851 & 1860 revolvers, #11 CCI cap, hardened steel
- Cone length: 0.285"
- Thread journal length: 0.200"
- Overall length: 0.485"
- Diameter of base: 0.295"
|
|
|
|
Nipple, 12-28 aka 5.5-.9mm metric thread, for most brands of.31/.36 Colt and Remington pocket revolvers and many Uberti 1851, 1860, 1861 Colt & 1858 Remington revolvers, Colt brand second generation 1851 & 1860 revolvers, #11 CCI cap, stainless steel
- Cone length: 0.285"
- Thread journal length: 0.200"
- Overall length: 0.485"
- Diameter of base: 0.295"
|
|
|
|
Nipple, 12-28 thread, for Thompson Center Seneca and Cherokee rifles, & T/C Patriot pistol, #11 CCI cap, stainless steel
- Cone length: 0.300"
- Thread journal length: 0.200"
- Overall length: 0.500"
- Diameter of base: 0.305"
Use nipple wrench #NW-170
|
|
|
|
Nipple, 6-.75mm metric thread, for Investarm Gemmer Hawken, Lyman Great Plains, Deerstalker, Trade Rifle #11 CCI cap, stainless steel
- Cone length: 0.375"
- Thread journal length: 0.195"
- Overall length: 0.570"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 6-.75mm metric thread, for Lyman Great Plains Rifle, Trade Rifle & InvestArm rifles, musket cap, stainless steel, requires a well centered hammer cup!
- Cone length: 0.440"
- Thread journal length: 0.195"
- Overall length: 0.635"
- Diameter of base: 0.307"
|
|
|
|
Nipple, 7-.75mm metric thread to REPAIR Lyman Great Plains Rifle & Pistol, Trade Rifle, InvestArms, Cabela's Hawken and other Italian replica rifles, #11 CCI cap, stainless steel
- Cone length: 0.440"
- Thread journal length: 0.195"
- Overall length: 0.635"
- Diameter of base: 0.307"
7-.75mm threads to be used to repair rifles with damaged 6-.75mm factory threads. Use a 7-.75mm tap to enlarge the damaged threads. Dope the nipple threads with #BC-CTL choke-tube-lube before first insertion of this snug nipple.
|
|
|
|
Nipple, 6-.75mm metric thread, for InvestArms, Cabela's Hawken rifles, #11 CCI cap, stainless steel
- Cone length: 0.440"
- Thread journal length: 0.195"
- Overall length: 0.635"
- Diameter of base: 0.307"
|
|