Your search for 'ramrods'
returned
973 results.
|
English Sporting Rifle , .58 caliber, 32" Green Mountain barrel, maple, iron trim, percussion, new, unfired, by J.A. Wymore
This slender halfstock sporting rifle is stocked in maple and trimmed in browned iron furniture with a poured pewter forend cap. The slender shaping on the maple stock combined with the 32" long straight octagon barrel give this rifle a modest weight and handy length, making it ideal to carry afield. As new, unfired, this rifle was neatly hand asse
|
|
Enfield Musketoon , .58 caliber, 24" barrel, percussion, walnut, brass, used by Davide Pedersoli & Co.
This Enfield Musketoon, with 24" barrel, is dated 1861 on the lock plate. Made for the caliber .577 hollow base Minie bullet that allowed quick reloading, achieved fine accuracy, and much longer range than the round ball muskets of an earlier generation. The rear sight is calibrated and marked in 100 yard increments, up to 600 yards. Enfield musket
|
|
Hawken Rifle , .54 caliber, 36" Douglas XX barrel, walnut, iron, percussion, fine quality, used, signed by Robert S. Hannahs
If you are a muzzle loading expert, you recognize this handsomely finished Hawken rifle as the work of the famous custom gun maker, Robert Hannahs, The House of Hawken, Kenosha, Wisconsin . Made in 1972, it is used with only a few scattered handling marks on the stock. Made for a 6'0" or taller shooter, this rifle has a full 14-3/8" trigger reach.
|
|
Canoe Gun , 20 gauge, 24" octagon-to-round barrel, Chambers' English flintlock, maple, iron, used
This short barreled canoe guns is stocked in maple with a round faced flintlock. Made without a rear sight, this gun qualifies for NMLRA trade gun match events, shooting patched round balls at paper targets, and shot charges at clay birds. It will be a powerful short range hunting gun, very handy when hunting from a boat or in thick brush. Trigger
|
|
Loading Block, for .50 caliber patched round ball, 2-3/8" x 5", maple, sanded, unfinished
This miniature "bread board" shaped accoutrement is made from hard maple, drilled to hold six lubricated patches and round balls. Before hunting, grease your patch, center it over a hole, and press the ball into the patch, forcing it into the hole, using our #ST-7 short starter. Press it into the hole, until the ball protrudes beyond the far side.
|
|
Gun Craftsmanship Manuals - 8 Piece Set
This set includes the following manuals by master gunsmith Kit Ravenshear: Craft and Practice - Part 1: Re-conversion, Screw Threads, Assembling Locks, etc. 20 pages. Craft and Practice - Part 2: Ramrods, Pipes, Sheet Metal Work, Top Jaw Screws, etc. 25 pages. Metalwork - Part 1: Cleaning, Hardening, Ageing & Colouring, etc. 17 Pages. Meta
|
|
Rifles of the American Indians , by Ryan R. Gale, Larry Ness, Gary Mikelson
Now shipping! Rifles of the American Indians by authors Ryan R. Gale, Larry Ness, and Gary Mikelson is our newest work on the subject of Native American rifles. Filled with hundreds of full color images of dozens of original trade and treaty rifles, this book's wide 11" landscape format allows images up to 22" across the gutter. This books allo
|
|
Ball puller , steel screw, .32 caliber brass collar, 10-32 thread
Blued steel ball pullers with caliber specific brass collar, with 10-32 threads to fit Thompson Center, CVA, Lyman, Traditions, and most Italian or Spanish guns. When pulling a stuck ball we recommend alway lubricating the ball and using a high strength ramrod with a secure tip to remove a ball.
|
|
Ball puller , steel screw, .36 caliber brass collar, 10-32 thread
Blued steel ball pullers with caliber specific brass collar, with 10-32 threads to fit Thompson Center, CVA, Lyman, Traditions, and most Italian or Spanish guns. When pulling a stuck ball we recommend alway lubricating the ball and using a high strength ramrod with a secure tip to remove a ball.
|
|
Ball puller , steel screw, .40 caliber brass collar, 10-32 thread
Blued steel ball pullers with caliber specific brass collar, with 10-32 threads to fit Thompson Center, CVA, Lyman, Traditions, and most Italian or Spanish guns. When pulling a stuck ball we recommend alway lubricating the ball and using a high strength ramrod with a secure tip to remove a ball.
|
|
Ball puller , steel screw, .45 caliber brass collar, 10-32 thread
Blued steel ball pullers with caliber specific brass collar, with 10-32 threads to fit Thompson Center, CVA, Lyman, Traditions, and most Italian or Spanish guns. When pulling a stuck ball we recommend alway lubricating the ball and using a high strength ramrod with a secure tip to remove a ball.
|
|
Ball puller , steel screw, .50 caliber brass collar, 10-32 thread
Blued steel ball pullers with caliber specific brass collar, with 10-32 threads to fit Thompson Center, CVA, Lyman, Traditions, and most Italian or Spanish guns. When pulling a stuck ball we recommend alway lubricating the ball and using a high strength ramrod with a secure tip to remove a ball.
|
|
Ball puller , steel screw, .54 caliber brass collar, 10-32 thread
Blued steel ball pullers with caliber specific brass collar, with 10-32 threads to fit Thompson Center, CVA, Lyman, Traditions, and most Italian or Spanish guns. When pulling a stuck ball we recommend alway lubricating the ball and using a high strength ramrod with a secure tip to remove a ball.
|
|
Ball puller , steel screw, .58 caliber brass collar, 10-32 thread
Blued steel ball pullers with caliber specific brass collar, with 10-32 threads to fit Thompson Center, CVA, Lyman, Traditions, and most Italian or Spanish guns. When pulling a stuck ball we recommend alway lubricating the ball and using a high strength ramrod with a secure tip to remove a ball.
|
|
Ball puller , steel screw, .62 caliber brass collar, 10-32 thread
Blued steel ball pullers with caliber specific brass collar, with 10-32 threads to fit Thompson Center, CVA, Lyman, Traditions, and most Italian or Spanish guns. When pulling a stuck ball we recommend alway lubricating the ball and using a high strength ramrod with a secure tip to remove a ball.
|