Thompson Center New Englander Shotgun, 12 gauge, 28" barrel, percussion, walnut, iron trim, sling mounts, used

Home > Guns > Percussion guns > Percussion rifles

Thompson Center New Englander Shotgun,
12 gauge, 28" barrel,
percussion, walnut, iron trim,
sling mounts, used

Part Number:	AAW-423
Availability:

This Thompson Center New Englander Shotgun has a 28" tapered round barrel with a polished blue finish. The walnut stock has very few handling marks. The buttstock and ramrod pipe have factory mounts to attached a quick disconnect sling swivel. Trigger reach is 13-3/4" and this shotgun weighs 6.5 pounds.

The12 gauge bore is bright and clean. The cylinder bore measures .725" at the muzzle, and can be used with either lead or bismuth shot, or a patched round ball for larger game. A small brass bead is fitted near the muzzle to serve as a front sight. No rear sight is installed in typical fowling gun fashion.

The hooked breech allows the barrel to be easily dismounted for cleaning without risk of wetting the stock with water containing black powder residue. To dismount the barrel, put the lock on half cock, withdraw the ramrod, drift the keys past the underlugs, and the barrel can be lifted from the barrel channel for ease of cleaning. Remove the nipple and place the breech end of the barrel in a bucket of soapy water. Run a wet patch down and up the bore, the pumping action will flush all the fouling from the barrel. Once the bore is clean, run a dry patch down the bore to pick up any moisture followed by a oily patch. Dry and oil the exterior then reassemble the rifle.

The walnut stock is in near-new condition, with only a few very minor handling marks. The trigger guard is wide to accept a gloved finger. The blued buttplate is stamped with the TC logo. The wooden ramrod is fitted with a blued loading tip. The hidden tip is threaded to accept 5/16-27 shotgun loading and cleaning accessories.

Our lock view shows the color case hardened percussion lock, factory engraved by Thompson Center. The breech is fitted with a 1/4-28 threaded stainless steel nipple. This lock works smoothly, with a strong mainspring, and fly detent. The trigger provides a smooth release of the lock. Note, the New Englander model is the only T/C model that requires removing the tang to dismount the lock due to the overhang on the breech plug tang.

This Thompson Center New Englander Shotgun with serve you well both in the field and at the range. This is a nice example of a T/C New Englander with the factory cylinder bore barrel that has been well maintained. Order it for a ten day visual inspection. You will be delighted. Else if it does not fit you, return it in unfired condition for same-day refund. Postage is your only risk, when you order any one-of-a-kind gun from Track, whether new, used, or antique.

Ready to order? Click VIEW CART in the upper right of the screen, review items and quantities, then click CHECK OUT. Enter your name, address, and billing information for prompt shipment. Or, PRINT your order after entering your address, attach your check or money order, and send it by mail. Shipping cost is displayed after you enter your address.

Our web site displays actual in stock status, up-to-the-minute price, and shipping cost to every address in the USA and MOST OTHER COUNTRIES. International shipping cost for extra long or heavy parcels are determined after we weigh the parcel.

Ten day inspection begins at delivery. Send your approval. Else return it for same day refund, if not delighted. Postage is your only risk.

.690" round balls, pure lead, hand cast, per 25

Part Number:	BALL-690-X
Availability:
Price:	$18.69
Order Quantity:

Track's best Black Powder BORE CLEAN Solvent, with flip-top spout

Part Number:	BORE-CLEAN
Availability:
Price:	$4.59
Order Quantity:

Bore mop, 100% Cotton, for .75 caliber, 10-32 thread, washable

Part Number:	BORE-MOP-75-10
Availability:
Price:	$5.59
Order Quantity:

Bore brush, bronze, for .75 caliber, 10-32 thread

Part Number:	BRUSH-75-10
Availability:
Price:	$5.99

Brass Capper, for No. 11 caps, straight line, made in the USA, by Tedd Cash

Part Number:	CAPPER-P
Availability:
Price:	$12.59
Order Quantity:

English Powder Dipper, adjustable brass cup, calibrated in drams of black powder, patterned from an antique, made in the U.S.A.

Part Number:	DIPPER-P-35
Availability:
Price:	$33.95
Order Quantity:

English Shot Dipper, adjustable brass cup, calibrated in ounces of shot, patterned from an antique, made in the U.S.A.

Part Number:	DIPPER-S-15
Availability:
Price:	$33.95
Order Quantity:

Flush Nipple, 1/4-28 thread, stainless steel, with 1/4" square shank for nipple wrench, with tubing, fits Thompson Center

Part Number:	FLUSH-RST
Availability:
Price:	$4.99
Order Quantity:

Fouling Scraper, flat face, brass, .69 caliber, 10-32 thread

Part Number:	FS-69-10
Availability:
Price:	$5.19
Order Quantity:

Button jagged cleaning tip, 12 gauge, brass, 10-32 thread

Part Number:	JAG-12-10
Availability:
Price:	$4.29
Order Quantity:

Lee .690" round ball mold, single cavity, with handles

Part Number:	LEE-690
Availability:
Price:	$37.99
Order Quantity:

Handles, for bullet mold, LEE Commercial mold handles for six cavity molds, also fit Lyman, RCBS and similar mold blocks.

Part Number:	LEE-HANDLE
Availability:
Price:	$23.59
Order Quantity:

Mold, Lyman .690" round ball mold blocks, single cavity, use large handles

Part Number:	LYMAN-690
Availability:
Price:	$99.99
Order Quantity:

Handles for large mold blocks, by Lyman, fits all current single and double cavity molds

Part Number:	LYMAN-H-L
Availability:
Price:	$53.99
Order Quantity:

Powder measure, brass, adjustable 0 to 120 grains, with spout

Part Number:	MAS-120
Availability:
Price:	$22.99
Order Quantity:

Trapper's MINK OIL TALLOW, patch grease, for match shooting & cold weather hunting, one 8 oz. tin

Part Number:	MINK-OIL
Availability:
Price:	$8.59

Nipple Wrench for Rifles, short style, with slotted end

Part Number:	NW-160
Availability:
Price:	$9.99
Order Quantity:

Shooting patches, .015" cotton, .60 - .69 caliber, per 100, dry

Part Number:	OX-15-60-D
Availability:
Price:	$4.99
Order Quantity:

Shooting patches, .018" pillow ticking, .60 - .69 caliber, per 100, dry

Part Number:	OX-18-60-D
Availability:
Price:	$5.49
Order Quantity:

Shooting patches, .020" cotton, .60 - .69 caliber, per 100, dry

Part Number:	OX-20-60-D
Availability:
Price:	$4.99
Order Quantity:

12 gauge shotgun Premium Lubed Wad, bag of 100 lubricated felt wads

Part Number:	OX-WAD-12-W
Availability:
Price:	$14.99
Order Quantity:

Spring steel nipple pick, with bone bead handle

Part Number:	PICK-NIPPLE
Availability:
Price:	$3.59
Order Quantity:

Nipple, 1/4-28 thread, for standard rifle, #11 CCI cap, square shank, hardened steel, ideal for restoration

Cone length: 0.440"
Thread journal length: 0.195"
Overall length: 0.635"
Diameter of base: 0.307"

Part Number:	RST-I
Availability:
Price:	$4.99
Order Quantity:

Nipple, 1/4-28 thread, for standard rifle, #11 CCI cap, stainless steel

Cone length 0.440"
Overall length: 0.635"
Thread journal length: 0.195"
Diameter of base: 0.307"

Part Number:	RST-S
Availability:
Price:	$4.99
Order Quantity:

Ramrod tip, 7/16" diameter, brass, concave end, 10-32 thread, 1-1/2" long

Part Number:	RT-7-10-B
Availability:
Price:	$3.50
Order Quantity:

Buckshot #4 .240" round balls, lead, by Hornady, 5 pounds

Part Number:	SHOT-4
Availability:
Price:	$42.99
Order Quantity:

12 gauge, .740" ideal for .729" bore, .125" over powder card, 1000, by Circle Fly Wads

Part Number:	WAD-12-A
Availability:
Price:	$12.69
Order Quantity:

12 gauge, .740" ideal for .729" bore, .025" over shot card, 1000, by Circle Fly Wads

Part Number:	WAD-12-B
Availability:
Price:	$12.69
Order Quantity:

12 gauge, .740" ideal for .729" bore, .500" thick fibre wad, 500, by Circle Fly Wads

Part Number:	WAD-12-C
Availability:
Price:	$12.69
Order Quantity:

Patch puller, corkscrew worm, steel, brass base, 10-32 thread

Part Number:	WORM-CORK-10
Availability:
Price:	$6.89

Top of Page Home > Guns > Percussion guns > Percussion rifles