Thompson Center RENEGADE Rifle,
.50 caliber, 26" barrel,
walnut, iron, patridge sights,
assembled from a kit, used, by Thompson Center
Part Number: AAR-090
Availability: In Stock
Price: $299.00
Order Quantity:
This used Thompson Center RENEGADE .50 caliber percussion rifle was assembled from a kit. The stock still has a bit of excess wood on the lock panels and forearm. The barrel and iron furniture were finsihed to a brown which has aged to a silver gray patina. The rifle is used and has a few handling marks on the stock as well as a few minor marks in the barrel finish. This Renegade rifle is fitted with the patridge style front sight and square notch rear sight rather than the later bead sights. Weight is 7.9 pounds, and with a trigger reach of 13-3/4 inches, the rifle is perfectly setup for today's average man size shooter.

The .50 caliber, 1" octagon barrel is 26" in length. The bore appears to be mostly bright with a few pin prick speckles just inside the bore at the muzzle. The barrel is fitted with a patridge style front sight and square notched adjustable rear sight, unlike later production Renegades. Many shooters prefer these sights over the later imported sights. The rear sight windage and elevation adjustment screws are in good condition.

We recommend our #BALL-490 Hornady pure lead .490" round ball, #OX-15-50-D Ox Yoke .015" dry patch, #MINK OIL tallow lubricant, and 70 grains of #GOEX-FFg black powder for best accuracy. If hunting big game, in thick brush, try our 50 caliber Maxi-ball. Increase the powder charge as needed, to achieve best accuracy with this heavier bullet. Recoil will increase, but will not be noticed during the hunt.

The American black walnut stock has a very straight grain for strength. Used the stock has scattered handling marks. The blued steel buttplate is wide and nearly flat to spread the recoil from the .50 caliber bore over a large area. The wide trigger bow has ample room for the double lever, double set triggers.

The rifle is fitted with a hooked breech to simplify cleaning. To dismount the barrel place the lock at half cock, withdraw the ramrod, drift the wedge key past the underlug with our brass drift #TOOL-KEY-B. Once the wedge key is removed the barrel can be lifted from the stock. Remove the nipple and place the breech end of the barrel in a bucket of soapy water. Run a wet patch down and up the bore, the pumping action will flush all the fouling from the barrel. Once the bore is clean, run a dry patch down the bore to pick up any moisture followed by a oily patch. Dry and oil the exterior then reassemble the rifle.

Our lock view shows the color case hardened percussion lock, factory engraved by Thompson Center. This lock works smoothly, with a strong mainspring, and fly detent to allow the use of double set triggers. Notice the bright rainbow of mottled colors. Correctly adjusted, you may cock the lock, or set the trigger, in any sequence. Turn the tiny set trigger adjustment screw, between the two triggers, inboard to reduce the set trigger release tension. Or turn it fully inboard, to disable the set trigger feature, when hunting in very cold climates, where a numb finger might release the light set trigger too early. When training youngsters, we prefer to start with the set trigger disabled.

No cheek piece is carved on the T/C Renegade. Not to be confused with the T/C Renegade Hunter, this is the deluxe version with double set triggers. This is a good used example of a Thompson Center Renegade rifle. Our customers like these well made American guns, for their reliable service, durable reputation, accuracy, and good value. Order it for a ten day visual inspection. You will be delighted. Else if it does not fit you, return it in unfired condition for same-day refund. Postage is your only risk, when you order any one-of-a-kind gun from Track, whether new, used, or antique.

Ready to order? Click VIEW CART in the upper right of the screen, review items and quantities, then click CHECK OUT. Enter your name, address, and billing information for prompt shipment. Or, PRINT your order after entering your address, attach your check or money order, and send it by mail. Shipping cost is displayed after you enter your address.

Our web site displays actual in stock status, up-to-the-minute price, and shipping cost to every address in the USA and MOST OTHER COUNTRIES. International shipping cost for extra long or heavy parcels are determined after we weigh the parcel.

Ten day inspection begins at delivery. Send your approval. Else return it for same day refund, if not delighted. Postage is your only risk.

bullets, .50 caliber, Hornady Great Plains, 385 grain, pure lead, hollow base, hollow point, per 20
bullets, .50 caliber, Hornady Great Plains, 385 grain, pure lead, hollow base, hollow point, per 20
Part Number: BALL-50-385
Availability: In Stock
Price: $9.99
Order Quantity:
bullets, .50 caliber, T/C Maxi-Ball, hand cast pure lead, about 378 grains, per 20
bullets, .50 caliber, T/C Maxi-Ball, hand cast pure lead, about 378 grains, per 20
Part Number: BALL-50-MAXI
Availability: In Stock
Price: $9.99
Order Quantity:
.490" round balls, pure lead, Hornady, per 100
.490" round balls, pure lead, Hornady, per 100
Part Number: BALL-490
Availability: In Stock
Price: $12.59
Order Quantity:
Track's best Black Powder BORE CLEAN Solvent, with flip-top spout
Track's best Black Powder BORE CLEAN Solvent, with flip-top spout
Part Number: BORE-CLEAN
Availability: In Stock
Price: $3.99
Order Quantity:
Ball puller, steel screw, .50 caliber brass collar, 10-32 thread
Ball puller, steel screw, .50 caliber brass collar, 10-32 thread
Part Number: BP-50-10
Availability: In Stock
Price: $3.75
Order Quantity:
Bore brush, bronze, for .50 caliber, 10-32 thread
Bore brush, bronze, for .50 caliber, 10-32 thread
Part Number: BRUSH-50-10
Availability: In Stock
Price: $2.99
Order Quantity:
Brass Capper, for #11 caps, straight line, made in the USA, by Tedd Cash
Brass Capper, for #11 caps, straight line, made in the USA, by Tedd Cash
Part Number: CAPPER-P
Availability: In Stock
Price: $11.29
Order Quantity:
Track's Catalog 18,
432 pages, full color,
filled with Exact Full Size Photos
of most gun parts.
Track's Catalog 18, 432 pages, full color, filled with Exact Full Size Photos of most gun parts.
Part Number: CATALOG-18
Availability: In Stock
Price: $10.00
Order Quantity:
Fouling Scraper, flat face, brass, .50 caliber, 10-32 thread
Fouling Scraper, flat face, brass, .50 caliber, 10-32 thread
Part Number: FS-50-10
Availability: In Stock
Price: $3.79
Order Quantity:
Nipple, Hot Shot® for Thompson Center Hawken & other popular guns, 1/4-28 thread, #11 CCI cap, stainless steel

Cone length: 0.440" Thread journal length: 0.195" Overall length: 0.635" Diameter of base: 0.307"
Nipple, Hot Shot® for Thompson Center Hawken & other popular guns, 1/4-28 thread, #11 CCI cap, stainless steel
  • Cone length: 0.440"
  • Thread journal length: 0.195"
  • Overall length: 0.635"
  • Diameter of base: 0.307"
Part Number: HOT-SHOT-RST
Availability: In Stock
Price: $6.99
Order Quantity:
Jag, jagged cleaning tip, brass, .50 caliber, 3/8 rod, 10-32 thread
Jag, jagged cleaning tip, brass, .50 caliber, 3/8 rod, 10-32 thread
Part Number: JS-50-6-10
Availability: In Stock
Price: $4.25
Order Quantity:
Powder measure, brass, adjustable 0 to 120 grains, with spout
Powder measure, brass, adjustable 0 to 120 grains, with spout
Part Number: MAS-120
Availability: Item is currently sold out.
Price: $14.99
Order Quantity:
  
Trapper's MINK OIL TALLOW,
patch grease,
for match shooting & cold weather hunting,
one 8 oz. tin
Trapper's MINK OIL TALLOW, patch grease, for match shooting & cold weather hunting, one 8 oz. tin
Part Number: MINK-OIL
Availability: In Stock
Price: $6.99
Order Quantity:
Nipple Wrench for Rifles, short style, with slotted end
Nipple Wrench for Rifles, short style, with slotted end
Part Number: NW-160
Availability: In Stock
Price: $6.99
Order Quantity:
Shooting patches, .015" cotton, .50 - .59 caliber, per 100, dry
Shooting patches, .015" cotton, .50 - .59 caliber, per 100, dry
Part Number: OX-15-50-D
Availability: In Stock
Price: $3.29
Order Quantity:
Cleaning Patches, 2-1/2" diameter, bag of 100, pure cotton flannel, for .45 to .58 caliber
Cleaning Patches, 2-1/2" diameter, bag of 100, pure cotton flannel, for .45 to .58 caliber
Part Number: OX-CLEAN-58C
Availability: In Stock
Price: $3.89
Order Quantity:
Ramrod, 3/8" hickory, 48" long, brass tip, 10-32 thread
Ramrod, 3/8" hickory, 48" long, brass tip, 10-32 thread
Part Number: RAMROD-6-10-B
Availability: In Stock
Price: $15.99
Order Quantity:
Ramrod for Thompson Center Renegade, Renegade Hunter, or Big Boar Rifle,
3/8" brown Delrin nylon, 26-5/8" long. Brass tips are threaded 10-32 at rear, 8-32 at front.

Made by Track of the Wolf, in our Elk River, Minnesota, we make the brass tips and assemble the ramrod.
Ramrod for Thompson Center Renegade, Renegade Hunter, or Big Boar Rifle, 3/8" brown Delrin nylon, 26-5/8" long. Brass tips are threaded 10-32 at rear, 8-32 at front. Made by Track of the Wolf, in our Elk River, Minnesota, we make the brass tips and assemble the ramrod.
Part Number: RAMROD-265-TC
Availability: In Stock
Price: $17.99
Order Quantity:
Our Strongest Loading & Cleaning Rod, 5/16" stainless, over 29" long for T/C Hawken, rigid handle, 10-32 thread
Our Strongest Loading & Cleaning Rod, 5/16" stainless, over 29" long for T/C Hawken, rigid handle, 10-32 thread
Part Number: RAMROD-C-29-10
Availability: In Stock
Price: $24.99
Order Quantity:
Nipple, 1/4-28 thread, for standard rifle, #11 CCI cap, stainless steel
Cone length 0.440"Overall length: 0.635" Thread journal length: 0.195" Diameter of base: 0.307"
Nipple, 1/4-28 thread, for standard rifle, #11 CCI cap, stainless steel
  • Cone length 0.440"
  • Overall length: 0.635"
  • Thread journal length: 0.195"
  • Diameter of base: 0.307"
Part Number: RST-S
Availability: In Stock
Price: $4.99
Order Quantity:
Short Starter, patch & ball starter, 7/16" hickory rod for .50 caliber.
Short Starter, patch & ball starter, 7/16" hickory rod for .50 caliber.
Part Number: ST-7
Availability: In Stock
Price: $6.99
Order Quantity:
Patch puller, corkscrew worm, steel, brass base, 10-32 thread
Patch puller, corkscrew worm, steel, brass base, 10-32 thread
Part Number: WORM-CORK-10
Availability: In Stock
Price: $6.59
Order Quantity:
 
Track of the Wolf, Inc.
18308 Joplin St NW
Elk River, MN 55330-1773

For your convenience you can contact us via our on-line form
Contact the Webmaster if you have any problems with this site.
Privacy Policy        Copyright © 2018Track of the Wolf, Inc.
Accepted Credit Cards